The tapered barrel on these bushings is split on both sides, permitting them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for use with split-tapered sprockets and Split Taper Bushing china pulleys of the same bushing design. As you tighten the included screws, the bushing grips the shaft and pulls it in to the sprocket or pulley.
This Split Taper Bushing is designed exclusively for use with cast iron bushed bore pulleys and can be purchased on a single page as the pulley you will need. For work with with 5/8” shaft sizes. Comes with set screws. More Features: Made of Steel For employ with cast iron bushed bore pulley
Our stock metal Split Taper bushings feature wrench torque capability from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are used on sheaves, pulleys, sprockets and equipment belt pulleys. The split tapered bushing alleviates the necessity to have a component bored to size, preferably lowering readily available requirements and enabling changes in shaft size if necessary. The barrel of the split tapered bushing is definitely split in two spots and is definitely keyed to the shaft. The barrel OD is also keyed to the drive component aswell. The good thing about the split tapered bushing could it be will hold, whether or not the fasteners become loose. Split tapered bushings will be interchangeable between manufacturers.

Taper bushing are trusted together with sprockets, v-belt pulleys, timing pulleys, coupling and other mechanical parts with taper bore connections.
Taper bushing series are constructed with high quality engineered products with great tolerance. The feature is easy to employ and needs no more alteration. These bushings can suit almost a myriad of assemblies and sizes. They will be the best choice in design for mechanical connections.
To complete designations put bore size. For instance: PD1215X16MM designates a 1215 taper bushing with a 16mm bore.
No costly re-boring: full selection of both metric and imperial available.
Standard range meets up to 125mm/5″ shafts & Hub diameter required is determined by the application.
Complete short reach range readily available, for compact light-weight assemblies & Clean, Compact Design.
Ease of installation and removal.
This Split Taper Bushing is designed exclusively for use with cast iron bushed bore pulleys and will be purchased on the same page as the pulley you will need.
For use with 1 3/16” shaft sizes.
Includes 2 set screws.

Additional Features:
Made of Steel
For use with cast iron bushed bore pulley
This U1 Bushing with 5-1/2″ bore is a high-quality precision product that’s built for strength and strength. U1 bushings are being used in an extensively wide range of applications, which includes; sprockets, shaves, pulleys, gears, and much more, we also offer most of these goods. What sets this bushing apart may be the high-quality steel development along with precise manufacturing and top quality control; this means that you always get yourself a premium quality constant product. What really units us in addition to the other guys is our highly trained expert workers and our company-wide goal of customer satisfaction.
1. Be certain the tapered cone surfaces of the bushing and the within of the driven product will be clean and free from anti-seize lubricants.
2. Place the bushing in sprocket or various other part type that accepts the bushing.
3. Place cap screws loosely in pull-up holes. The bushing continues to be loose to assure sliding in shape on shaft.
4. With key on shaft, slide the sprocket or other part type to the desired location on the shaft. Make sure you keep the heads of the cap screws accessible.
5. Align the sprocket or part type, tighten the screws alternatively and progressively until they happen to be pulled up tight. Usually do not make use of extensions on the wrench handles and do not permit the sprocket or part to become drawn i connection with flange of bushing. At this time there must be a gap between your bushing flange and sprocket, make certain this gap will not close.
Twice split barrel ensures concentricity
Grips the shaft with great clamp fit
High torque carrying capacity
Permits blind assembly
Load not carried or tied to mounting screws
External key of all sizes for positive drive and increased torque carrying capabilities
Double-split barrel for confident clamping
Solid flange to maintain concentric bores
Available in inches, metric, and spline bores. Bore range between 3/8″ to 10″
Solid Flange & Twice Split Barrel – Assures better concentricity to the shaft.
Key to Key Drive – With keys in both the shaft and item to provide the strongest possible travel.
3/4″ per Foot Taper on Barrel – Self locking taper supplies the highest amount of mechanical locking product to product.
The tapered barrel on these bushings is split on both sides, allowing them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for apply with split-tapered sprockets and pulleys of the same bushing design. As you tighten the included screws, the bushing grips the shaft and pulls it in to the sprocket or pulley.
This Split Taper Bushing was created exclusively for use with cast iron bushed bore pulleys and can be purchased on the same page as the pulley you will need. For use with 5/8” shaft sizes. Includes set screws. Additional Features: Manufactured from Steel For apply with cast iron bushed bore pulley
Our stock steel Split Taper bushings feature wrench torque potential from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are used on sheaves, pulleys, sprockets and equipment belt pulleys. The split tapered bushing alleviates the need to have a component bored to size, preferably lowering on hand requirements and allowing for alterations in shaft size if required. The barrel of the split tapered bushing is certainly split in two places and is keyed to the shaft. The barrel OD is also keyed to the drive component aswell. The advantage of the split tapered bushing could it be will hold, even if the fasteners turn into loose. Split tapered bushings are interchangeable between manufacturers.